Luke Turner (@Enlightx) profile picture

Luke Turner

@Enlightx

IT Consultant in the Dudley Area. With an interest in electronics, Design. 3D Printing (Reprap) and Music

 Dudley, West Midlands
Enlightx.co.uk
Joined February 2009
  • Tweets4.1K
  • Following389
  • Followers217
717Media
Photo by Luke Turner (@Enlightx)Photo by Luke Turner (@Enlightx)Photo by Luke Turner (@Enlightx)Photo by Luke Turner (@Enlightx)Photo by Luke Turner (@Enlightx)Photo by Luke Turner (@Enlightx)Photo by Luke Turner (@Enlightx)Photo by Luke Turner (@Enlightx)Photo by Luke Turner (@Enlightx)
I published a Thing on @thingiverse! thingiverse.com/thing:503026… #thingalert

Sharkbyte Divimath TX5S.1 Adapter to 20x20 perfect for apex by Enlightx

makes the whoop vtx fit in a 20x20 style quad. use botsl to attached it to the frame with nyloc nuts then to hold the board in use bolts and a silicone oring to save it shorting and ad a little bit...

thingiverse.com
I published a Thing on @thingiverse! thingiverse.com/thing:449298… #thingalert

Matek M8Q-5883 GPS Holder by Enlightx

Just a little GPS holder for the matek M8Q-5883 gps unit so you can easily mount it to a GPS Stalk

thingiverse.com
I published a Thing on @thingiverse! thingiverse.com/thing:427455… #thingalert

Diatone Tinawhoop Crossfire Minimortal Antenna Mout by Enlightx

Print in TPU with no supports and should work fine.i find printing 2 sets helps layer times to be longer so your dont get a mess.i used the 2x4mm scres that come in the tinywhoop box but any m2 screw...

thingiverse.com
I published a Thing on @thingiverse! thingiverse.com/thing:415605… #thingalert

Stingy V2 Arm Protectors by Enlightx

Arm Bumpers for the X Hover Stingy V2 Frame.Gives 3mm of TPU protection all around the armalso a lip to make sure it doesnt move.Personally i mount on the bottom so motors are hard on the frame but...

thingiverse.com
I published a Thing on @thingiverse! thingiverse.com/thing:409758… #thingalert
Qav r 2 Arm Bumpers Skitzo Frame by Enlightx

Qav r 2 Arm Bumpers Skitzo Frame by Enlightx

Arm Bumpers for the QAV R 2. Designed using the Skizto frame but should the stock QAVR2 as well.2Strait fitGrip fir that grabs around the whole armdesigned to the fit on the bottom of the quad so the...

thingiverse.com
dont really use twitter much these days... more facebook groups. only signed in becayse twitter emailed me saying they were going to close account unless i agreed to new T&C. im still here. still 3d printing (dont build anymore just use them as tools) turned my talents to quads
I published a Thing on @thingiverse! thingiverse.com/thing:362635… #thingalert

SOURCE MICRO V0.1 Arm Guard and Motor softmount by Enlightx

Arm Guards for the Source Micro Frame from TBS (https://team-blacksheep.com/products/prod:source_micro)0mm is set at 2mm which should match the frame but you may be better off with the 0.2mm or 0.5mm...

thingiverse.com
I published a Thing on @thingiverse! thingiverse.com/thing:342624… #thingalert

Shendrones Squirt V2 Arm Brace by Enlightx

I broke my duct support arm on squirt v2 so decided to make an arm brace untill i can get a new frame.seems to work okay as its only supporting the duct .hope it helps you get out of a jam :)

thingiverse.com
1
I published a Thing on @thingiverse! thingiverse.com/thing:289795… #thingalert

iFlight XL7 7" Bottom battery pad by Enlightx

print this in TPU then you stick to the bottom (i used UPOL glue) then you can bottom mount a battery without fear of the screws pressing into your lipo on a crash. also help giving the battery a bit...

thingiverse.com
New year ... new printer
Image from Luke Turner (@Enlightx)
1
I can't even remember the spec of it it's been so long since it was built
Image from Luke Turner (@Enlightx)
Time to strip down my old arcade machine. Need room for vr space. Might rebuild it into an arcade stick and a pie box
Image from Luke Turner (@Enlightx)
When you don't have the correct brackets for your new car stereo you design and 3d print your own of course
Image from Luke Turner (@Enlightx)
4
Having a walk / lure fish
Image from Luke Turner (@Enlightx)
thats for a game that was released 3 years ago ! it was probs cheaper then on the dam wii u console. @NintendoUK lower your prices or fail
saw that lego city undercover has been redone for newer gen consoles and PC. @NintendoUK switch version its £49.00 WTF.. its £24.99 on PC!!
New quadcopter build. Tiny tiny brushless quad. had to wait over a month to get the parts from china
Image from Luke Turner (@Enlightx)
1
1
Good to go! Just waiting on lipos to charge
Image from Luke Turner (@Enlightx)
Now to give my Martian II a service before attempting to fly tommrow
Image from Luke Turner (@Enlightx)
It better not rain tomorrow morning!
Image from Luke Turner (@Enlightx)
Load more