RIP RAM
Both DIMMs with sequential serial numbers from a 2x32GB G.skill ripjaw V kit died after 5 years.
The other 2 identical DIMMs work fine in all slots.
They do have a lifetime warranty and aren’t marked EOL.. so I put in an RMA request and will see if they send me a new pair🤞
8
570
Working in loopback on the ECPIX-5
Keeping our dev methodology but with AI assistance, we've finally stabilized the USB3-PIPE project, implemented a proper USB3 Core, added support for Gowin/ECP5/Xilinx FPGAs and USB 3.2 Gen 1 (5Gbps) and Gen 2 (10Gbps).
This will also be an enabler for other projects: SLogic16U3, M2SDR, etc...
github.com/enjoy-digital/usb…
Submitted a PR that makes it 20% faster on ECPIX-5, hitting 432MB/sec each direction in duplex, up from 360MB/sec baseline. github.com/enjoy-digital/usb…
My favourite camping season. Looking out over the strait of Georgia towards Vancouver. Seals are fishing and barking just off shore and there’s a juvie bald eagle in a nest overhead.
2
4
304
$6.3B and all it took was popping one DevOps laptop..
Binance's initial investigation suggests that the security incident may involve a compromised DevOps engineer’s laptop, which allowed an attacker to gain access to a service container and submit unauthorized withdrawal transactions. We have found no evidence of any wallet private key leak. We will share a detailed technical post-mortem once the investigation is complete and the facts are fully verified.
The estimated total impact sits at around $6.3B. We have worked with blockchain partners to freeze affected assets, with ~$3 billion frozen on-chain so far.
Binance will cover all losses from the SAFU fund and the company’s funds. User funds are safe. We will also publish an updated Proof of Reserves once the remediation is complete.
As an immediate precaution, Binance has:
- temporarily suspended deposits and withdrawals while security checks are completed;
- revoked the affected address authorisation;
- engaged law enforcement and blockchain intelligence partners to trace and recover funds.
Our teams are working around the clock to resolve this issue safely and thoroughly. We are working closely with our law enforcement partners to confirm the identity of these criminals and bring them to justice.
Please rely only on official Binance channels for updates. Please feel free to contact Binance Customer Support if you have any further questions.
binance.com/en/support/annou…
3
295
ZFS pool went degraded… not one, but all 4 NVMe’s reporting SMART errors with 4% of their 600TB write endurance used. TRIM was enabled on the pool. They were mounted to a heatsink with active cooling on an x16 bifurcated carrier and ran cool.
Warranty expired 6 days ago.
I sent SanDisk logs and smartctl output and thankfully they made an exception to RMA all 4.
I don’t even want to look at what 1TB NVMe’s are going for these days…
Missed some holes and didn’t realize until I already reflowed.. back on the CNC with the same registration pins
17
529
This is the second time I've seen codex showing thinking text that is completely unrelated to any conversation I've had with it. Previously it was showing a message about a $5000 estimate being too high, and now that "preparations for years 11 versus 22 could become important".
What's going on here @thsottiaux @embirico @ajambrosino
1
1
276
I'm increasingly convinced high purity quartz (HPQ) may be part of the strategic interest in Greenland and Canada.
HPQ is critical to semiconductor manufacturing, particularly the crucibles used to grow silicon crystals. Global supply is overwhelmingly concentrated in Spruce Pine, North Carolina, where detailed reserve figures are closely guarded. How much is left? Good luck finding out.
What do Greenland and Canada have in common? Quartz.
Semiconductor crucibles require exceptional purity, typically 4N–5N (99.99–99.999% SiO2), with strict impurity limits.
Greenland has ~6 million tonnes of estimated quartz at Ivittuut, with samples reaching ~3N purity. But with 80% of the island buried under ice and much of its geology underexplored, that may be just the tip of the iceberg. Its true HPQ potential remains largely unknown.
In Canada it gets interesting.
BC: Deposits at Mt. Rose and Armstrong have reportedly been successfully refined to 4N8 purity.
Manitoba: An estimated 15 BILLION tonnes of silica in situ. Sio Silica reports approximately 540 million tonnes potentially recoverable, describes it as the world's largest deposit, and claims laboratory processing has achieved 5N purity.
If even a small fraction of Canada's enormous silica resources can economically produce crucible grade HPQ, it's of extreme strategic value, especially given the unknown remaining reserves at Spruce Pine.
3
7
504
Reflowing some Infineon AS5047U magnetic position sensors to try out. I’ve used the D variant before which work very well, but high res needed SPI readout.
These have SPI for config and angle readout plus PWM, UVW, and ABI outputs but this U variant has full 14 bit, 16384 count resolution on ABI.
ABI is much more deterministic, lower latency with less overhead on an MCU with timers that support quadrature encoders in hardware, since you just need a single cycle read or a DMA trigger to get the angle.
They also have angular velocity estimators, averaging filters, and dynamic angle correction DSPs that compensate for internal delays vs angular velocity
Next going to try this RC Novak 540 10.5T motor. It has hall sensors which I’ll hookup to the JST hall input of the board later, trying senseless BEMF first
The firmware is built around deterministic runtime graphs. Can switch between sensor feedback, sensorless control and different observers over CAN. Shared STM32 drivers support HRTIM and advanced timers; BSPs provide board mappings. Reconfigure, tune and save without reflashing.
Finished bringup of the STM32 G474 LMG5200 half bridge GaN 3 phase BLDC controller board.
Testing using a small gimbal motor in FOC with sensorless BEMF observer feedback
"Compiling rust is slow"
Running cargo clean, then a release build and linking of a workspace with 14 member crates that depend on the heavy Bevy game engine with custom shaders using kache and dynamic linking. 17.8 seconds on a M3 MacBook Pro.
This builds the CNC CAM software I've been working on for milling PCBs from Gerber/Excellon or KiCad board design files.
Building without cleaning the workspace is even faster when iterating on the design.
1
279
























