Astartes eunt domus! 加油

Let’s do a primer on in-flight ice accumulation, or “icing” for those not familiar. As you go up in altitude, the temperature & pressure decrease. It’s about 2°C per 1,000’, called the “standard lapse rate”. It varies locally, but we use this as our standard. So, even on a hot day on the surface at 90°F (32°C), you theoretically only need to climb 16,000’ to get to 32°F (0°C). Because of the way air flows over the surfaces of an airplane at speed, the outside air temperature is not equal to the temperature of the air as it hits the wing & such. Friction & compression heats the air as it hits the airplane; we measure this & call it the “Total Air Temperature” (TAT). The faster you go, the higher the TAT. Still, most jets can’t go fast enough at altitude to get the TAT above freezing. In fact, on the 737 at near max speed & a cruise altitude of 35,000’ or so, the TAT is still going to be around -40°C (it varies a lot, that’s just a guess). Now, clouds are just visible moisture. We all know what happens to water at those temperatures. An airplane passing through a bunch of frozen water is going to collect ice on it. There are different categories, types & intensities of icing. Structural icing is just the airplane flying through cold clouds; the ice collects on the airplane. It can be Rime icing, which is kind of milky in color & looks bubbly, Clear icing, which can be tough to see or a mix. In some rare scenarios, very large drops of water are supercooled & remain liquid until they contact the jet, then instantly freeze. While the other types of ice generally only collect on the leading edges of surfaces, supercooled drops may run back over more of the jet during the freeze. That’s a big problem; usually only the leading edges of the surfaces like the wings & engines are protected from ice. The shiny parts on the front of airliner wings & around the engine intake are where hot air from the engines gets diverted to heat up that area & melt any ice…but if ice goes beyond that, there isn’t much you can do. Some airplanes have systems to prevent ice formation on the tail, too, but that’s usually electric pads & usually only shows up on T-tail jets. Anyway, regardless of the type, you may get various intensities: trace, light, moderate or severe ice. Induction icing occurs in the engines, as it sucks air in & changes the pressure. You can get induction icing without structural icing, but again, the area around the engine inlet is heated to prevent large chunks of ice from forming, breaking off & going through the engine. We treat icing as a possibility anytime there is visible moisture (rain, snow, fog, clouds) and the temperature is 10°C or below. Yeah, you won’t get structural icing at 10°C, but you might get induction icing. In these conditions, the engine anti-ice is turned on, sending hot air around the leading edge of the engines. The wing anti-ice is used a bit differently & the philosophy here varies widely by airline. I’ve always used it not as an anti-ice, preventing ice from forming like on engines, but as a de-ice…it’s not turned on until I see ice forming. Other airlines have different philosophies. I turn it on, melt the ice, then turn it off. Now, we can’t see the wings well, so on the 737 we use the windscreen wipers as a proxy for the wings. If the large nut on the wiper arm has collected ice, I assume the wings have, too (the windscreens are electrically heated, but it’s not unusual to go through moderate or severe icing & collect some ice around the edges of the windscreen). If you recall, I said the tail often doesn’t have an ice system, and that’s true of the 737. That may sound scary, but it’s not something I’m worried about. If we turn on the wing anti-ice during a flight, the computer assumes the tail may have ice on it & it bumps our approach speed up to give the tail extra air to manipulate. It’s basically an ICE additive to our final approach speed. I hope that helps, I’m out of space.

Happy Halloween! Remember: there is no smoking within 12 hours of flying & no drinking within 50’ of the jet.

Perhaps the most famous airplane ghost story: Eastern Airlines flight 401 crashed into the Florida Everglades shortly before midnight on Dec 29, 1972. The crash was avoidable; a malfunctioning landing gear light distracted the pilots, the yoke was bumped, the autopilot disconnected & the L-1011 jet slowly spiraled into the swamp without anyone noticing. 101 were killed. Now, it’s not uncommon for airlines to salvage useable parts in the aftermath of a crash. Flight 401 was no different; useable parts were recovered & *allegedly* used as spares across Eastern’s L-1011 fleet. According to stories, the ghosts of the Captain & Flight Engineer began to appear aboard jets that used the salvaged parts, warning flight crew of problems that were developing on the jet. Eastern executives were unhappy & warned that sharing such stories was unprofessional. It’s *alleged* that they then ordered all the salvaged parts to be removed from their jets & disposed of, after which the ghost reports stopped. A book was written on the subject, “The Ghost of Flight 401”, which was developed into a TV movie. It also appears in other media from time to time. A second book claimed that the parts had never been installed on other jets & that nobody had reported ghost sightings. The whole thing was just a myth. I don’t believe in ghosts, but certain non-critical parts are definitely salvaged in crashes. They have to be re-certified, but can be used again. Critical parts like wing spars & engines are much less likely to be reused. I don’t pay much heed to these stories, but it seemed appropriate to share tonight!